355
When it is done, it will jump back to the Sample Chops screen:
By adjusting the Chop parameter, it is now possible to select and audition the chop points that LD3
has found.
Audition the chop points by hitting the “Play” button. If some chop points are not exactly where
you would like them to be, adjust them with the Adjust parameter. If some chop points shouldn’t
be there, delete them by hitting the “Del” button.
It is also possible to adjust the end point of the chop point. Simply touch the
NEXT
button. Now,
while auditioning the selected chop point, you can adjust the next chop point, which is also the
end point for the selected chop point, using the Adjust parameters.
To add chop points, first touch the “Play” button, to make the sample/chop point play back. While
the sampling is playing back, hit the “Add” button when it is playing back the point, where you
would like to add a chop point.
In the bottom of the screen, it shows the position of the selected chop, in the values that the
Sample Start
parameters would have to be adjusted to, to select this point of the sampling. So if
you don’t want to use the chop points anyway, but just wants the sample playback to start at this
point, you can exit to the Sample Rec page, and set the Sample Start point to this value.
When you are satisfied with the chop points, remember to hit the “Save” button to keep them.
The chop points are saved together with the sample data, and are also imported/exported via
USB as cue points.
Summary of Contents for Little deFormer 3
