21
When the
Func/Mute
button is held down, it is possible to
mute/unmute
the 16 note tracks, by
pushing any of the 16 step buttons. When it is lighting up, the 16 step buttons functions as
Quick
Jump
buttons, that will take you to the edit pages, which names are showed right above each step
button.
When the
Steps/Part
button is held down, the 16 step buttons functions as
Part Select
buttons.
Pushing any of these, will select part 1 to 16.
When it is lighting up, the 16 step buttons will show the
steps
of the selected sequencer note
track. Steps that are on will light up, steps that are off will not light.
The
Volume
knob always adjusts the audio output volume.
The
Edit 1-8 Knobs
to the left of the display, adjusts the parameters on each edit page. On the
Preset Select screen
, they acts as modulation sources, that controls any parameters that has
knob1 to 8 set as modulator, and transmits MIDI CC’s. Any Edit Knob, that has not been assigned
as a modulator to any parameter, acts as a
Quick Edit Knob
.
The Quick Edit Knobs controls:
-Edit Knob 1: Digital filter 1 cutoff (
MIDI CC#4
).
-Edit Knob 2: Digital filter 1 resonance (
MIDI CC#5
).
-Edit Knob 3: Digital filter 1 mix (
MIDI CC#8
).
-Edit Knob 4: VCA envelope release time (
MIDI CC#9
).
-Edit Knob 5: Digital filter 2 cutoff (
MIDI CC#10
).
-Edit Knob 6: Digital filter 2 resonance (
MIDI CC#11
).
-Edit Knob 7: Digital filter 2 mix (
MIDI CC#12
).
-Edit Knob 8: The level of the selected part (
MIDI CC#7
).
When the knobs is not assigned to any modulation destinations, they will work as Quick Edit
knobs. When they work as Quick Edit knobs, and MIDI CC’s are received, these will be received
per
part
.
When the Edit Knobs are assigned as modulation sources, to any modulation destination, they will
work
globally
.
The Morph knob and the Seq Morph knob will always work globally.
Summary of Contents for Little deFormer 3
