246
Dest:
Track modulation destination. Selects what should be modulated on the track. Choices are:
-Note:
The note numbers of the track will be modulated.
-Gate:
The gate times of the track will be modulated.
-Dly:
The delay times of the track will be modulated.
-Swing:
Swing modulation will be applied to the track. This is a bit more fine than the delay time
modulation.
-Velo:
The velocity values of the track will be modulated.
-Pos:
The position subtrack positions will be modulated.
-Strum:
The Strum parameter will be modulated.
Amount:
Adjusts the amount of modulation that will be applied to the track.
Start:
Sets the track start step. This will be the step, the track starts at, when hitting the Start/Stop
button, or when entering this preset from another preset, while the sequencer is running. When
selecting another preset, while the sequencer is running, the preset change will happen, when
Note track 1 are at the step before the start step. Step 1 to 64 can be selected.
The Start step can be set globally for all tracks at the Seq Main page.
Trps:
Track transpose. Will transpose the note numbers of the whole track up to 64 semitones up
or down.
Prob:
Track Note Randomizer Probability. When this is turned fully up, all programmed note steps
of the track will play back. The more it is turned down, the less notes will play back. The notes the
will not play back are selected randomly.
Rtim:
Track Note Randomizer Time. When turned up, it will create random delays on the
programmed note steps triggering.
Strum:
When the track is playing more than one note at the same time, the more the Strum
parameter is turned up, the longer the delay between each note will be.
Summary of Contents for Little deFormer 3
