323
The Song Edit Page
To enter the Song Edit page, just touch SEQ on the navigation bar at the top of the More… page:
On the Song Edit page, you have an overview of the programmed song steps, and the possibility of
editing these.
By touching any of the song steps, you can select this step for editing. The selected step is shown,
boxed in blue. The little brown square between the step number and the preset name, is showing
what song step is currently being played back.
For each song step, the song step number is shown, the preset number and name, and the
number of times track 1 will play back (under the X).
To edit a song step, turn edit knob 1 to select <End>, preset bank A to P, or <Loop>. <End> will
make song playback stop, when it reaches that step, <Loop> will make it jump back to song step 1,
and start all over again.
Turn edit knob 2 to select the preset number, and edit knob 3 to select the number of times, you
want track 1 to play back, for that step.
Push and hold the Func/Mute button, to mute/unmute tracks on the selected song step, via the
step buttons. Only tracks that are unmuted in the preset itself, can be muted by the song
sequencer.
Summary of Contents for Little deFormer 3
