228
-AudCH:
Chopped audio track. When the audio track is recorded, chop points are inserted at each
sequencer step, according to the resolution setting of the selected track. See the “Audio Tracks”
section later in this manual.
Metro:
Metronome Off, On, Rec.
-Off:
The metronome is off, and will make no sound.
-On:
The metronome is on, and when the sequencer is playing, it will put out a click to audio
output 1, every time note track 1 passes a 4/4 beat. Every time note track 1 starts over, it will
make a click that is slightly higher pitched than the other clicks.
-Rec:
When the sequencer is playing, and realtime rec is activated, it will put out a click to audio
output 1, every time note track 1 passes a 4/4 beat. Every time note track 1 starts over, it will
make a click that is slightly higher pitched than the other clicks.
Length:
Global tracks length. Sets the step length for all the 4 Note tracks and 8 Controller tracks
equal with one parameter. From 1 to 64 steps. Track lengths can be set individually for each track,
in the separate track menu’s.
Notes:
Sets if the notes of the Note tracks should be shown in a note grid (setting: Grid), or as
value bars (setting: Value). This can also be switched on the note track pages.
StAdv:
Step Advance on/off. When step recording a sequence, it will automatically advance to the
next step of the selected track, is this is set to on.
Skip:
Turning this up, will cause the sequencer to randomly skip some beats here and there. The
more it is turned up, the more it will skip.
This affects all sequencer tracks at the same time.
Start:
Global tracks start step. Sets the start step for all the 4 Note tracks and the 8 Controller
tracks equal with one parameter. From step 1 (default) to step 64. Track steps can be set
individually for each track, in the separate track menu’s.
The buttons of this page:
Rec:
This will toggle
realtime recording
on and off.
Realtime recording
can be switched on and off
at any time, regardless of if the sequencer is playing or not. The sequencer must though play, to
make it possible to input notes in realtime.
See “Realtime recording of notes” later in this section.
Summary of Contents for Little deFormer 3
