30
Selecting Sequencer Note Track steps 1-16, 17-32, 33-48 and 49 to 64 / + Controller tracks steps
65-80, 81-96, 97-112, 113-128:
Push and release the
Func/Mute
button, so that it is lightning up. Now, push and release step
button 1,
Bar Sel
:
Now step button 1,
Bar Sel
, will light up.
Note tracks: When you are located on any other pages, than the sequencer controller tracks
pages, bar is selected to be viewed for a note track. The selected bar, is the bar that is shown on
the step buttons, and on the note track pages.
Hit Bar Sel, so that it lights up. Now step buttons 2 to 5 will select bar 1 to 4, of the currently
selected track. The button of the bar that is selected, will light up. The other 3 bar select buttons
will flash.
Controller tracks: When you are located on any of the controller track pages, bar is selected to be
viewed for the currently selected controller track. The selected bar, is the bar that is shown on the
controller track pages.
Hit Bar Sel, so that it lights up. Now step buttons 2 to 9 will select bar 1 to 8, of the currently
selected track. The button of the bar that is selected, will light up. The other 7 bar select buttons
will flash.
When pushing a bar button, that is already selected, both on note and controller tracks, the
function of the Edit Knobs will now be toggled: Parameters > Knobs1-8 > Knobs 9-16.
Summary of Contents for Little deFormer 3
