329
LD3 will now show the Preset select page. The REC indicator on the preset select page, has now
turned red, indicating that LD3 is in recording mode. Song realtime recording can also be switched
on or off, by touching the REC indicator.
If you selected an empty song, the last preset you selected, before you jumped to song mode, will
be shown. If you selected a song that was already recorded, the preset on the selected step of this
song will be shown.
Now, if the shown preset are the preset you would like to have on step 1 of your song, you can
proceed recording your song, by pressing the Start/Stop button.
If you would like another preset on step 1 of your song, please select this, using the preset select
field, and then push the Start/Stop button, to start the recording of the song.
The preset you selected will now start to play back.
From here you can now select other presets, at the time you want these to play back in your song.
Preset changes will only be registrered and recorded, when track 1 of the currently playing preset
reaches its end and starts over. When the changes has been registrered, the song step number in
the position ruler will increment by one.
While any preset is playing back, it is possible to mute/unmute the sequence tracks. Push and hold
the Func/Mute button, and switch tracks on or off, using the step buttons.
Summary of Contents for Little deFormer 3
