406
MIDI Specs
Receives:
-Note on/offs on the LD3 global MIDI channel and on the individual part MIDI channels in Multi-
timbral mode. These can trigger the parts and be recorded by the sequencer, when it is in reatime
rec mode.
-MIDI CC 1, 2, 4, 5, 7, 8, 9, 10, 11 and 12 on the LD3 global MIDI channel and on the individual part
MIDI channels in Multi-timbral mode. All parameters that are set up to be controlled by Edit Knob
1 to 8, are also controlled by these MIDI CC’s.
Morph Knob: CC1
Seq Morph Knob: CC2
Edit Knob 1: CC4
Edit Knob 2: CC5
Edit Knob 3: CC8
Edit Knob 4: CC9
Edit Knob 5: CC10
Edit Knob 6: CC11
Edit Knob 7: CC12
Edit Knob 8: CC7
CC16, touch screen keyboard Y-position on the part zone midi channel, regardless of, if LD3 are in
multi-timbral mode or not.
MIDI CC’s 17 to 61 as modulation sources.
MIDI CC 64, MIDI Sustain Pedal. Values above 64: Hold notes, values below 64: Release notes.
-Pitch Bend messages on the LD3 global MIDI channel and on the individual part MIDI channels in
Multi-timbral mode. Controls the oscillators and samplers of part 1 to 16, and any parameter that
has pbend set as its modulation source.
-MIDI clock and start/stop messages are received if the sequencer are in external sync mode.
Summary of Contents for Little deFormer 3
