Gorenje Aqua ECOLOGIC Instructions For Use, Maintenance And Installation Manual Download Page 31 | Manualshive

Page: 31 / 112

Gorenje Aqua ECOLOGIC Instructions For Use, Maintenance And Installation Manual Download Page 31

AQUA ECOLOGIC | instructions for use, maintenance and installation |

September 2015

31

Push button -

Pressing while the stove is running decreases the set power.

With the last pressing of the MENU button, this push-button decreases the desired
room temperature.

By pressing the menu we select a submenu.

MENU button

By briefly pressing the home screen, the display will show the set value for the room
temperature that can be adjusted by pressing the + and -.

Pressing for more than 2 seconds will activate the display menu.

Pressing for more than 4 seconds will activate the advanced settings of the menu. By
continuing to press this button we will see all menu options one after the other.

For the choice of the parameter in the submenu we use the + and - buttons. By
pressing the MENU button again we activate the flashing of the set parameter values,
which can be adjusted by pressing the + and -.

Briefly press the ON/OFF button to return to the initial display.

«
...
29
30
31
32
33
...
»

Summary of Contents for Aqua ECOLOGIC

















































































































Reviews:

No comments