GE Solar 8000M/i Service Manual Download Page 80

Page: 80 / 192

4-28

Solar 8000M/i patient monitor

2026265-075C

Maintenance and checkout:

Checkout procedure

10. Set the

LIGHT

and

MODULATION

switches as follows:

Set the

LIGHT

switch to

LOW

Set the

MODULATION

switch to

HIGH

Set the

RATE

switch to

201

11. Verify the following SpO2 readings for saturation and pulse rate:

Saturation (%): 81 ± 2

Rate (bpm): 201 ± 3% (195 to 207)

NBP calibration check

1. Connect the acquisition device to the patient monitor.

2. Disconnect all parameter cables.

3. Apply power to the patient monitor.

4. Make sure the power indicator on the acquisition device’s front panel

is ON (green).

WARNING

Do not

put the NBP cuff around a human limb during the

checkout procedure due to the potential for injury. When
the NBP cuff is used in this procedure, it must be tightly
wrapped around a rigid cylinder or pipe.

5. Connect a manometer and NBP cuff to the NBP connector on the

front of the acquisition device.

Connect to

acquisition device

454A

Summary of Contents for Solar 8000M/i

































































































































































































Search results

Summary of Contents for Solar 8000M/i

Reviews:

Related manuals for Solar 8000M/i

Brands by name

Popular brands

GE Solar 8000M/i, Service Manual

Search results

Summary of Contents for Solar 8000M/i

Reviews:

Related manuals for Solar 8000M/i

Brands by name

Popular brands