GE Solar 8000M/i Service Manual Download Page 87

Page: 87 / 192

2026265-075C

Solar 8000M/i patient monitor

4-35

Maintenance and checkout:

Checkout procedure

3. Attach a jumper between pin 1 (Marker Out) and pin 2 (Marker In) of

the

DEFIB SYNC

connector and observe negative spikes in the R-

waves of the displayed ECG waveforms.

4. Remove the jumper.

Marker Out (Frequency)

Signal Pin:

Ground Pin:

Probe Type:

x10

Time/Division:

0.2S

Volts/Division:

Marker Out (Pulse Width)

Signal Pin:

Ground Pin:

Probe Type:

x10

Time/Division:

5mS

Volts/Division:

025A

026A

Observe normal R-
waves before the
jumper is installed.

Observe negative spikes in the R-waves while
the jumper is installed. Note that the spikes are
small, and can be difficult to see at times.

040A

Summary of Contents for Solar 8000M/i

































































































































































































Search results

Summary of Contents for Solar 8000M/i

Reviews:

Related manuals for Solar 8000M/i

Brands by name

Popular brands

GE Solar 8000M/i, Service Manual

Search results

Summary of Contents for Solar 8000M/i

Reviews:

Related manuals for Solar 8000M/i

Brands by name

Popular brands