GE Solar 8000M/i Service Manual Download Page 67

Page: 67 / 192

2026265-075C

Solar 8000M/i patient monitor

4-15

Maintenance and checkout:

Electrical safety tests

NOTE

If either reading is greater than the appropriate specification
below, the device under test fails. Contact GE Technical Support.

A (0.01 volts on the DMM) at 120 VAC using the test body.

A (0.02 volts on the DMM) at 240 VAC using the test body.

A (0.05 volts on the DMM) at 120-240 VAC using the ECG

cable.

NOTE

The 10 and 20

A limits are based on internal design standards.

The 50

A limit is common to all standards. AAMI ES-1 standard

requires using the patient cable.

6. Set the power switch on the device to OFF.

7. Repeat the steps in this procedure using the appropriate SpO2 Test

Body. Connect the SpO2 Test Body to the blue SpO2 connector of the
device under test.

Test completion

1. Disconnect the leakage tester from the power outlet.

2. Disconnect all test equipment from the device.

3. Disconnect the device power cord from the leakage tester.

Summary of Contents for Solar 8000M/i

































































































































































































Search results

Summary of Contents for Solar 8000M/i

Reviews:

Related manuals for Solar 8000M/i

Brands by name

Popular brands

GE Solar 8000M/i, Service Manual

Search results

Summary of Contents for Solar 8000M/i

Reviews:

Related manuals for Solar 8000M/i

Brands by name

Popular brands