GE Solar 8000M/i Service Manual Download Page 44

Page: 44 / 192

3-6

Solar 8000M/i patient monitor

2026265-075C

Installation:

Back panel connections

DFP VID 1 and 2

Two DFP (Digital Flat Panel) connectors provide an interface to digital
displays. The connector is a 20-pin, MDR type.

RS-232 1

The

RS-232 1

serial connector provides an interface to the iPanel

computer. If not using an iPanel, it interfaces to a PC for software
upgrades or polled-parameter service. The connector is a 9-pin, D type.

RS-232 2

The

RS-232 2

serial connector provides a touchscreen interface. The

connector is a 9-pin, D type.

NOTE

Use cable 2006733-00X for touchscreen connection. The cable
supplied with the display will not work.

014C

Summary of Contents for Solar 8000M/i

































































































































































































Search results

Summary of Contents for Solar 8000M/i

Reviews:

Related manuals for Solar 8000M/i

Brands by name

Popular brands

GE Solar 8000M/i, Service Manual

Search results

Summary of Contents for Solar 8000M/i

Reviews:

Related manuals for Solar 8000M/i

Brands by name

Popular brands