GE AKTAprocess Operating Instructions Manual Download Page 88

Page: 88 / 180

4.4

ÄKTAprocess Setup

Precaution

CAUTION

To prevent bacterial growth, ÄKTAprocess may be partly filled with
denaturated alcohol (18% C

OH (ethanol), 2% C

OH (iso-

propanol) and 80% H

O (water)) at delivery.

The denatured alcohol mixture can be hazardous to humans if
consumed.

Flush out the denaturated alcohol before assembling, testing or
integrating ÄKTAprocess into the intended process context.

In this section

See page

Section

4.4.1 Assembly of ÄKTAprocess

4.4.2 Setup of control system and network

4.4.3 Connect compressed air supply

4.4.4 Guidelines for connections

100

4.4.5 Connect sample pump

102

4.4.6 Connect a column

ÄKTAprocess Operating Instructions 29-0252-49 AA

4 Installation

4.4 ÄKTAprocess Setup

Summary of Contents for AKTAprocess





















































































































































































Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands

GE AKTAprocess, Operating Instructions Manual

Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands