manualshive.com logo in svg

GE AKTAprocess, Operating Instructions Manual

Share
Download
GE AKTAprocess Operating Instructions Manual Download Page 7

1.2

Important user information

Read this before operating
ÄKTAprocess

All users must read the entire Operating Instructions before installing, operating or
maintaining ÄKTAprocess.

Always keep the Operating Instructions at hand when operating ÄKTAprocess.

Do not operate ÄKTAprocess in any other way than described in the user documentation.
If you do, you may be exposed to hazards that can lead to personal injury and you may
cause damage to the equipment.

Intended use of ÄKTAprocess

ÄKTAprocess is a low-pressure automated liquid chromatography system intended for
the precision transportation of fluids to and from chromatography columns of varying
sizes. The system is intended for process scale-up and large-scale pharmaceutical
manufacturing.

ÄKTAprocess is not suitable for operation in a potentially explosive atmosphere or for
handling flammable liquids.

WARNING

Do not operate ÄKTAprocess in any other way than described in
ÄKTAprocess user documentation.

ÄKTAprocess Operating Instructions 29-0252-49 AA

7

1 Introduction

1.2 Important user information

Summary of Contents for AKTAprocess





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands