GE AKTAprocess Operating Instructions Manual Download Page 13

Page: 13 / 180

CE marking

The CE marking and the corresponding Declaration of Conformity is valid for the instru-
ment when it is:

•

used as a stand-alone unit, or

•

connected to other CE marked instruments, or

•

connected to other products recommended or described in the user documentation,
and

•

used in the same state as it was delivered from GE Healthcare, except for alterations
described in the user documentation.

UL conformity

The system is listed according to UL508a.

A UL inspection report is provided in the documentation package.

Regulatory compliance of
connected equipment

Any equipment connected to ÄKTAprocess should meet the safety requirements of EN
61010-1/IEC 61010-1, or relevant harmonized standards. Within EU, connected equipment
must be CE marked.

ÄKTAprocess Operating Instructions 29-0252-49 AA

1 Introduction

1.3 Regulatory information

Summary of Contents for AKTAprocess





















































































































































































Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands

GE AKTAprocess, Operating Instructions Manual

Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands