GE AKTAprocess Operating Instructions Manual Download Page 25

Page: 25 / 180

WARNING

Take extra care to make sure that the sample pump trolley does
not overturn when moving the trolley.

WARNING

The sample pump must be positioned so that it does not interfere
with access to the emergency stop buttons.

WARNING

The sample pump must be powered from the system. It must not
be connected directly to mains power.

CAUTION

The handles on the sample pump trolley must not be used for lifting.

System operation

WARNING

Safe distance. Always maintain a safe distance from
ÄKTAprocess during drainage or other activities that may involve
splashing.

WARNING

Cabinet doors. During operation, all doors must always be closed
and locked.

ÄKTAprocess Operating Instructions 29-0252-49 AA

2 Safety instructions

2.1 Safety precautions

Summary of Contents for AKTAprocess





















































































































































































Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands

GE AKTAprocess, Operating Instructions Manual

Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands