manualshive.com logo in svg

GE AKTAprocess, Operating Instructions Manual

Share
Download
GE AKTAprocess Operating Instructions Manual Download Page 38

2.4

Recycling information

Introduction

This section contains information about the decommissioning of ÄKTAprocess.

Decontamination

ÄKTAprocess shall be decontaminated before decommissioning and all local regulations
shall be followed with regard to scrapping of the equipment.

Disposal, general instructions

When taking ÄKTAprocess out of service, the different materials must be separated and
recycled according to national and local environmental regulations.

Recycling of hazardous
substances

ÄKTAprocess contains hazardous substances. Detailed information is available from
your GE Healthcare representative.

Disposal of electrical
components

Waste electrical and electronic equipment must not be disposed as unsorted municipal
waste and must be collected separately. Please contact an authorized representative
of the manufacturer for information concerning the decommissioning of equipment.

38

ÄKTAprocess Operating Instructions 29-0252-49 AA

2 Safety instructions

2.4 Recycling information

Summary of Contents for AKTAprocess





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands