manualshive.com logo in svg

GE AKTAprocess, Operating Instructions Manual

Share
Download
GE AKTAprocess Operating Instructions Manual Download Page 163

8

Reference information

About this chapter

This chapter provides reference information that may become useful when installing,
operating, maintaining and troubleshooting ÄKTAprocess. Further information to assist
in ordering parts and accessories is also provided.

The ÄKTAprocess is a modular built instrument that can be configured in many different
ways.

To understand the specific configuration that applies to ÄKTAprocess, please refer to
the product documentation package supplied with the instrument.

In this chapter

This chapter contains the following sections:

See page

Section

164

8.1 Specifications

167

8.2 Chemical resistance

169

8.3 Gradient performance

171

8.4 Decontamination report

172

8.5 UNICORN method for system CIP/Sanitization/Rinsing

175

8.6 Further information

ÄKTAprocess Operating Instructions 29-0252-49 AA

163

8 Reference information

Summary of Contents for AKTAprocess





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands