GE AKTAprocess Operating Instructions Manual Download Page 33

Page: 33 / 180

Description

Symbol/text

Warning! Before connecting the system, make sure that
the system setting corresponds with the power supply.

Disconnect switch and branch circuit to be provided by
installer.

NOTE!

Different power supply cables in CE/UL systems

Brown

White

Green or
Yellow/green

Yellow/green

Protective Earth

Make sure that authorized personnel perform electrical
connections and use appropriate power supply plug.

Attention: cleaning only when USB cover is closed!

Note:

This label is located beside the USB port on the side
panel of the monitor.

Attention:

cleaning only
when USB cover
is closed!

C0035304-01

ÄKTAprocess Operating Instructions 29-0252-49 AA

2 Safety instructions

2.2 Labels

Summary of Contents for AKTAprocess





















































































































































































Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands

GE AKTAprocess, Operating Instructions Manual

Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands