manualshive.com logo in svg

GE AKTAprocess, Operating Instructions Manual

Share
Download
GE AKTAprocess Operating Instructions Manual Download Page 65

3.4

Optional components

Introduction

ÄKTAprocess can be ordered or upgraded with a range of optional components. This
section briefly describes the optional components.

Extra system pump inlets

Up to eight extra inlets with individually controlled valves can be installed.

This means that ÄKTAprocess is able to manage up to ten individual inlets for system
pump A.

Extra system outlets

Up to eight extra system outlets with individually controlled valves can be installed.

This means that ÄKTAprocess is able to manage up to ten individual outlets in total.

System pump B

ÄKTAprocess can be provided with a second system pump. The addition of a second
system pump enables ÄKTAprocess to operate as a gradient system.

The B-pump can be provided with up to six individually controlled inlets.

If the System pump B option is selected, an extra flow meter can also be provided to
enable the individual pump flows, as well as the total system flow, to be measured.

The B-pump type is identical to the A-pump.

In-line filter

A filter can be installed between the air trap and the column to prevent foreign objects
from contaminating the column. Different types of in-line filter are available, including
a disposable capsule filter option. Filter housings may be made of steel or polypropylene.

ÄKTAprocess Operating Instructions 29-0252-49 AA

65

3 System description

3.4 Optional components

Summary of Contents for AKTAprocess





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands