manualshive.com logo in svg

GE AKTAprocess, Operating Instructions Manual

Share
Download
GE AKTAprocess Operating Instructions Manual Download Page 20

CAUTION

Do not touch the system while pumping fluid through the system
that has a temperature above the normal working temperature.
Do not touch the system until you are sure that this can be done
without risk and when all components in the system have reached
the normal working temperature range.

CAUTION

Use ear protection whenever working close to the system in
operation.

Installing and moving

WARNING

ÄKTAprocess must be installed and prepared by GE Healthcare
personnel or third party authorized by GE Healthcare.

WARNING

Move transport crates. Make sure that the forklift has capacity to
safely lift the crate weight. Make sure that the crate is properly
balanced so that it will not accidentally tip when moved.

WARNING

The system is not fitted with lifting eye bolts or other devices for
lifting with telphers or similar equipment. The system should only
be lifted using the lower part of the frame.

WARNING

Heavy object. Because of the significant weight of
ÄKTAprocess, great care must be taken not to cause squeezing or
crushing injuries during movement. At least two, but preferably
three or more, persons are recommended when moving the unit.

20

ÄKTAprocess Operating Instructions 29-0252-49 AA

2 Safety instructions

2.1 Safety precautions

Summary of Contents for AKTAprocess





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands