GE AKTAprocess Operating Instructions Manual Download Page 102

Page: 102 / 180

4.4.6

Connect a column

Introduction

This section outlines the steps needed to connect a column to ÄKTAprocess.

Important

NOTICE

Make sure that the connections to the column and system comply
with the requirements in the column and system Operating Instruc-
tions.

Considerations for AxiChrom
columns

AxiChrom columns can be packed using ÄKTAprocess and Intelligent Packing.

Small diameter columns, up to 200 mm diameter, use ÄKTAprocess pumps to drive the
adapter hydraulically.

Larger AxiChrom columns, 300 mm diameter and above, use an AxiChrom Master con-
nected to the ÄKTAprocess Profibus connector.

See respective AxiChrom column manuals for information on hose connections.

For more details regarding using AxiChrom with ÄKTAprocess, refer to the AxiChrom
user manual.

Preparations

The air sensor alarm(s) before the column must be disabled before filling the system/col-
umn with liquid (Alarms:Air_Alarm:Disabled).

102

ÄKTAprocess Operating Instructions 29-0252-49 AA

4 Installation

4.4 ÄKTAprocess Setup
4.4.6 Connect a column

Summary of Contents for AKTAprocess





















































































































































































Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands

GE AKTAprocess, Operating Instructions Manual

Search results

Summary of Contents for AKTAprocess

Reviews:

Brands by name

Popular brands