GE AIR C18 Service Manual-Installation Download Page 47

Page: 47 / 60

—

③

Ceiling Mount of Unit Body

1. Initial Installation of Indoor Unit

●

Attach the suspending frame base to the suspending bolt. Nuts and washers must be used at the upper and

lower sides of the suspending frame base to secure it. The locating plate

⑦

can prevent the washer from falling

off.

●

Refer to the installation paper mould

⑤

for the dimensions of the ceiling opening.

●

The installation paper mould marks the center of the ceiling opening.

●

The label of the unit and the installation paper mould all mark the center of unit.

●

Use screw

⑥

(3 pieces) to install the installation paper mould

⑤

to the unit and use screws to fix the angle of the

drainage groove at the outlet of the pipe.

2. Adjust the position of the unit so that it is in the correct installation position (refer to Figure 3)

3. Check if the unit is horizontal

●

The indoor unit is equipped with built-in draining pump and level tube

●

In case the unit inclines toward the direction opposite the flow direction of condensate water, the float switch

may suffer from failure, so that dripping is caused.

4. Remove the washer locating plate

⑦

for preventing the washer from falling off. Tighten the nut on it.

5. Remove the installation paper mould.

Warning : Please tighten the nuts and bolts to prevent them from dropping.

Nuts (provided by user on site)
Washer

③

(accessory)

Suspending Frame Base

Tightening (Double Nuts)

(Secure the suspending frame base)

Inserting In

Locating Plate of Washer

⑦

(accessory)

(Secure the washer)

Level Tube

Polyethylene pipe

Center of Ceiling Opening

Screw

⑥

(accessory)

The screw beside the pipe outlet is secured
at the corner of the drainage groove

Installation Paper Mould

⑤

Screw

⑥

(accessory)

(Secure the Installation Paper Mould)

Summary of Contents for AIR C18





























































Search results

Summary of Contents for AIR C18

Reviews:

Related manuals for AIR C18

Brands by name

Popular brands

GE AIR C18, Service Manual-Installation

Search results

Summary of Contents for AIR C18

Reviews:

Related manuals for AIR C18

Brands by name

Popular brands