GE AIR C18 Service Manual-Installation Download Page 46

Page: 46 / 60

—

11.2

Installation Dimension Drawing

①

Selection of Installation Position

1. The air inlet and air outlet of the indoor unit must be far away from obstacles to ensure that airflow can reach every

corner of the room;

2. Ensure the installation of indoor unit is in conformity with the requirements of installation dimension drawing;

3. Choose a place where four times of the weight of indoor unit can be withstood and operating noise and vibration are

not increased;

4. The installation position must been horizontal;

5. Choose a position where condensation water can be easily discharged and the air-conditioning water system can be

easily connected;

6. Ensure sufficient clearance and space for service and maintenance; Ensure the unit is at least 1800cm from the floor;

7. Use suspending bolts for the installation. Check if the installation position can withstand four times the weight of the

unit. In case it is not the case, reinforce the installation position before installing the unit (refer to the installation paper

mould to find out the points to be reinforced).

Caution :
1. Ensure the cooking smoke extractor above the gas stove has

enough capacity of extracting smoke, so that the smoke is not
suctioned by the air-conditioning unit.

2. Ensure the air-conditioning unit is far away from the kitchen, so

that cooking smoke is not suctioned by the air-conditioning unit.

②

Dimensions of Ceiling Opening and Position of Suspending Bolt

（

M10

）

Caution :
The dimension of the ceiling opening marked with * can be as long as 910mm, but the length of the overlapping part
between the ceiling and the decorative from panel shall be at least 20mm.

Keep enough

clearance

With enough exhaust capacity

Cooking Smoke Extractor

Gas Stove

950 D

cor

ont

Panel

* C

ilin

840 U

780

ranc

e betw

een Su

pend

ing Bo

Refrigerant Pipe

Suspending Bolts

（×

）

680 Clearance between

Suspending Bolts

840 Unit

890 Ceiling Opening

950 Decorative Front Panel

Body Installation Frame

Ceiling

A Direction

20 mm

Summary of Contents for AIR C18





























































Search results

Summary of Contents for AIR C18

Reviews:

Related manuals for AIR C18

Brands by name

Popular brands

GE AIR C18, Service Manual-Installation

Search results

Summary of Contents for AIR C18

Reviews:

Related manuals for AIR C18

Brands by name

Popular brands