GE AIR C18 Service Manual-Installation Download Page 50

Page: 50 / 60

—

●

Method of filling water

Draining Outlet for Service Purpose (with Rubber Plug)
(This outlet is only for discharging the water inside the
drainage groove)

⑥

Electrical Line Layout

●

All supplied components, materials and electrical operation must be in conformity with the local laws and regulations.

●

The power supply must be of rated voltage of the unit and special electrical line for air-conditioning.

●

For electrical operation, refer to the

“

Electrical Diagram

”

attached on the unit.

●

All installation of electric lines must be carried out by professional electricians.

●

A circuit breaker must be installed for the purpose of cutting off the power supply of the whole system when needed.

●

Grounding measures must be taken.

●

Carry out installation in accordance with the state line layout rules.

Drainage Pipe

Cover Plate of

Check Hole

above 100mm

Plastic Spray Can

(The pipe shall be around

100mm long)

(Fill water from the air outlet side)

Summary of Contents for AIR C18





























































Search results

Summary of Contents for AIR C18

Reviews:

GE AIR C18, Service Manual-Installation, Page: 50 / 60

Search results

Summary of Contents for AIR C18

Reviews: