GE AIR C18 Service Manual-Installation Download Page 19

Page: 19 / 60

—

Controller and Remote Controller Function Manual and Operating Instructions

7.1 Controller and Remote Controller Function Manual 1

7.1.1 Temperature Parameters

◆

Indoor preset temperature (T

preset

)

◆

Indoor ambient temperature (T

amb.

)

◆

Outdoor condenser temperature (T

cond.

)

7.1.2 Basic Functions

Under any mode, the compressor will keep running within 6 minutes once it is started (except under overfull protection).

Once stopped, it cannot be restarted until after 3-minute delay. When outdoor fan is started, run at high speed for 8

seconds and then switch to desired speed.

7.1.2.1 Cooling Mode

7.1.2.1.1 Cooling Conditions and Process

When T

amb.

≥

preset

℃

, the unit will run under cooling mode, in which case the compressor and outdoor fan will be

started and the indoor fan will run at low speed.

When T

amb

≤

preset

-1

℃

, the unit will be stopped under cooling mode, in which case the compressor and outdoor fan will

be stopped and the indoor fan will run at preset speed.

When T

preset

-1

℃

amb.

< T

preset

℃

, the unit will maintain its original operating status.

Under this mode, the switchover valve will be de-energized and the temperature can be set within a range from 16 to

℃

7.1.2.2 Dehumidifying Mode

7.1.2.2.1 Working Conditions and Process of Dehumidifying

When T

amb.

> T

preset

℃

, the unit will run under cooling mode, in which case the compressor and outdoor fan will be

started and the indoor fan will run at low speed.

When T

preset

-2

℃≤

amb.

≤

preset

℃

, the compressor, indoor unit and outdoor fan will run 6 minutes and stop 4 minutes

in repeated cycle, while the indoor fan will run at low speed.

When T

amb.

< T

preset

-2

℃

, the compressor, outdoor fan and indoor fan will be stopped.

Under dehumidifying mode, the temperature can be set within a range from 16 to 30

℃

amb

preset

℃

preset

-1

℃

Start cooling

Original operating status

Stop cooling

6 min.

Preset speed

Run

Stop

6 min.

3 min.

amb

preset

℃

preset

-2

℃

Cooling

Stop cooling

Run

Stop

Low speed

Dehumidifying

Compressor

Indoor fan

Outdoor fan

Compressor

Indoor fan

Outdoor fan

6 min.

4 min.

Summary of Contents for AIR C18





























































Search results

Summary of Contents for AIR C18

Reviews:

GE AIR C18, Service Manual-Installation, Page: 19 / 60

Search results

Summary of Contents for AIR C18

Reviews: