background image

 28 

 

 

8.2  Disassembly Procedures of Indoor Unit 

 

 

Operating Procedures / Photos    Applicable Unit Models: GE AIR C24, C34, C41 IN      

 

 

Disassemble Front Grill Sub-Assy 

Push the left and right clasps of the front grill to 

the center and lift them at the same time. After 

the front grill is in the 45

°

angle position, pull it 

backward. (refer to Figure 8-1) 

 

 

 

 

  Disassemble Front Panel   

Manually unplug the connection joints of guide 

louver motor cable and the limit switch cable. At 

the left clasp, use screw driver to twist off the 

screw of electric box cover 

, Disassemble the 

electric box cover 

and then unplug the 6-core 

cable plug. At the left clasp, manually pull the 

four corner outer covers outward to remove 

them. Use screwdriver to screw off the four 

screws, turn the front panel anticlockwise, and 

then pull it upward to remove it. (refer to Figure 

8-2, 8-3 and 8-4) 

 

 

 

Disassemble Water Tray 

Manually unplug the socket connector of motor 

cable. Use screwdriver to screw off the screw 

fixing the temp. sensor and the motor cable. 

Push the water level switch cable, water pump 

cable and temp. sensor cable aside. Use 

screwdriver to screw off the four screws and pull 

the water tray upward to remove the water tray. 

refer to Figure 8-5, 8-6 and 8-7

 

 

 

 

Figure 8-5 

Left Clasp 

Right Clasp 

Figure 8-1 

6-core cable 

plug 

Electric Box 

Cover II 

Electric Box 

Cover I

 

Figure 8-2 

Figure 8-3 

Figure 8-4

Corner Outer Cover 

Screw

Electric Box Cover I

Screw

Summary of Contents for AIR C18





























































Reviews: