background image

 41 

 

           

Care and Maintenance

 

                                                                  Warning

 

z

  Be sure to stop the unit and plug off the power before cleaning your 

air conditioner. Otherwise, electric shock may happen.   

z

  Don’t splash water on indoor unit, it may cause the risk of electric 

shock.  

z

  Volatile liquids such as thinner or gasoline will cause damage to the 

appearance of air conditioner. (Only use soft dry cloth or wet cloth soaked with neutral detergent to 
clean the indoor unit). 

 
 

10.1 

    Clean the front panel 

 

 

Clean the front panel   

Clean the surface of front panel with soft wet cloth and then gently wipe it with dry cloth. 

 

Remove front grill

 

Use your hand to push the left and right clamp on front 
grill to the middle. At the same time, lift them up to 
form 45

 angle. Pull the front grill backward to 

remove it.   

 

Clean the front grill

 

Clean the surface of front panel with soft wet cloth and 
then gently wipe it with dry cloth. 

 

Install the front grill

 

Use your hand to put the front grill into front case at an 
angle of 45

, making the front hook jointed to the 

groove of front case. Then, use your hand to push the 
left and right clamp on front grill to the middle. Close 
the front grill.   
 
 

10.2 

  Clean the air filter

 

 

 

Remove the air filter

 

From the grooves on two ends of the front panel, pull 
the front panel open to an angle along the arrow direction. Then, pull the 
air filter downward to remove it, as shown on right.   

 

Clean the air filter

 

Clean the filter with vacuum cleaner. If the filter is too dirty, wash with 
warm water (below 45

) that is added with neutral detergent. Then dry it 

at a cool place, as shown on right.   

 

Install the air filter

 

Push the air filter into the groove of front grill. Use your hand to push the 
two clamps inward and close the filter.   
 
 
Notes: 
Never expose the front grill or air filter directly under the sun. Never clean 
it with hot water over 45

  or dry it on fire, (as this will cause decoloring, 

fire or deformation). 
 

 

Summary of Contents for AIR C18





























































Reviews: