GE AIR C18 Service Manual-Installation Download Page 21

Page: 21 / 60

—

7.1.3 AUTO ON/OFF and Sleep

71.3.1 AUTO ON/OFF

◆

AUTO ON

When the timer is set to ON, the system will be under AUTO OFF status. At the time for AUTO ON, the controller will

remain under its preset mode. The time interval for AUTO ON or OFF is 0.5h, and can be set within 0.5 - 24 hours.

◆

AUTO OFF

You can set AUTO OFF function when the unit is under ON status. Upon the time of AUTO OFF< the system will be

switched off. The time interval for AUTO OFF is 0.5h, and can be set within 0.5 - 24 hours.

7.1.3.2 Sleep

If the controller is under cooling or dehumidifying mode, the preset temperature will be increased by 1

℃

one hour

after running under sleep mode, and increased by another 1

℃

after 2 hours. Totally 2

℃

will increased in 2 hours.

After that, the unit will run at this temperature.

If the controller is under heating mode, the preset temperature will be decreased by 1

℃

one hour after running

under sleep mode and will be decreased by another 1

℃

after two hours. The temperature will decreased by 2

℃

within two hours. After that, the unit will run at this temperature.

No sleep function under fan mode or auto mode.

7.1.4 Other control

7.1.4.1 Indicator Control

7.1.4.1.1 Indoor Unit Indicator

1. The Run Indicator (red) will be bright when the unit is started and be black when the unit is stopped.

The Run Indicator will blink under one of following conditions upon start of the unit:

Definition of Faults and

Protection

Display of Run Indicator

Notes:

System High-pressure

Protection

Black for 3 seconds and

blink once

Indoor Antifreeze

Protection

Black for 3 seconds and

blink 2 times

System Low-pressure

Protection

Black for 3 seconds and

blink 3 times

Compressor Air-out

Protection

Black for 3 seconds and

blink 4times

Communication Fault

Run Indicator

Black for 3 seconds and

blink 6times

The Run

Indicator will

blink under

one of

following

conditions

upon start of

the unit:

2. AUTO ON/OFF Indicator (yellow): It is bright under AUTO ON/OFF or Sleep mode; otherwise it is black.

The AUTO ON/OFF indicator will blink under one of following conditions upon start of the unit:

preset

℃

preset

℃

preset

1 hours

2 hours

Over 2 hours

1 hours

2 hours

Over 2 hours

preset

-1

℃

preset

-2

℃

preset

Summary of Contents for AIR C18





























































Search results

Summary of Contents for AIR C18

Reviews:

Related manuals for AIR C18

Brands by name

Popular brands

GE AIR C18, Service Manual-Installation

Search results

Summary of Contents for AIR C18

Reviews:

Related manuals for AIR C18

Brands by name

Popular brands