manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 8

XG1200 User's Guide 

8/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

6.4.2 Procedure for Extracting Maintenance Information when a System Loop has Occurred .........................218

 

6.4.3 Procedure for Extracting Maintenance Information when an XG1200 Malfunction Occurs......................218

 

Chapter 7

 

Troubleshooting...............................................................................................................................219

 

7.1 Restoring Factory Defaults ..............................................................................................................................220

 

7.1.1 Resetting startup-config to Factory Defaults.............................................................................................220

 

7.1.2 Selecting Firmware....................................................................................................................................220

 

7.1.3 Restoring Factory Defaults........................................................................................................................221

 

Appendix A

 

Event Logs ....................................................................................................................................223

 

A.1

 

Overview of Event Logs...............................................................................................................................223

 

A.2

 

List of Event Logs ........................................................................................................................................224

 

A.2.1

 

env (Supervisory Control: 0

-

999) .......................................................................................................224

 

A.2.2

 

Basic XG1200 Control: 100

-

1999 ......................................................................................................226

 

A.2.3

 

kernel: (Layer 2 Basic Control: 2000-2999) ..........................................................................................227

 

A.2.4

 

Npm (Network Protocol Control: 3000-3299)........................................................................................232

 

A.2.5

 

clim (Basic CLI Control: 3300-3999) .....................................................................................................235

 

A.2.6

 

xgsh (CLI Command History: 4000-4499) ............................................................................................236

 

A.2.7

 

rstp (Rapid Spanning Tree Control: 4500-4999) ...................................................................................236

 

A.2.8

 

lacp (LACP Control: 5000-5499) ...........................................................................................................237

 

A.2.9

 

sys (Maintenance Support Function: 7400-7499) .................................................................................237

 

A.2.10

 

update (Firmware Update: 7500-7999)..............................................................................................238

 

A.2.11

 

snmp (SNMP Control: 8500-8599).....................................................................................................241

 

A.2.12

 

ntp (NTP Control: 8600-8699)............................................................................................................242

 

A.3

 

Message Format for Forwarding syslog ......................................................................................................243

 

Appendix B

 

SNMP Traps ...................................................................................................................................244

 

Appendix C

 

List of MIBs ...................................................................................................................................245

 

Index.........................................................................................................................................................................255

 

 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands