manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 181

XG1200 User's Guide 

181/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

5.14.19 clear statistics 

Function 

Clears all of statistics which have been stored after the startup of system hardware. 

 

The following statistics are cleared. 

 

Traffic statistics       : traffic-bytes, traffic-counts and framesize-traffic-counts 

 

QoS traffic statistics      : qos-priority-traffic-bytes and qos-priority-traffic-counts 

 

VLAN traffic statistics    : vlan-traffic-bytes and vlan-traffic-counts 

 

Data flow statistics    : dataflow 

 

Error traffic statistics    : error 

Prompt 

xg# 

Command syntax 

clear statistics

 

 

Command type 

Operation management command 

Note 

 

If you issue this command during execution of “monitor” command in the “current” mode, the “monitor” command may 
temporarily display incorrect statistics. If it has occurred, wait until the statistics are updated automatically in the next 
updating interval or reissue the “monitor” command. The “monitor” command will display the correct statistics. 

Example 

Clear all of statistics which have been stored after the system startup. 

xg# clear statistics 

 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands