manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 161

XG1200 User's Guide 

161/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

Output format (if “total” is specified) 

xg# monitor traffic-counts total 
Traffic  Statistics(Total  Frame  Counts)         2005/08/22-12:12:15 
================================================================== 
Port  Link  State/   Tx-Frames     Rx-Frames    Rx-Bcast     Rx-Mcast 
      STP  State     Counts         Counts        Counts       Counts 
----  ------------  -----------   ----------   ----------   ----------- 
   1  Up/Discard    1234567890K   1234567890K  1234567890K  1234567890K 
   2  Down                       0               0             

 

0              0 

   3  Up/Discard    1234567890K   1234567890K  1234567890K  1234567890K 
   4  Up/Learn     

 

1234567890K   1234567890K  1234567890K  1234567890K 

   5  Up/Forward    1234567890K   1234567890K  1234567890K  1234567890K 
   6  Up/Forward    1234567890K   1234567890K  1234567890K  1234567890K 
   7  Down           1234567890K   1234567890K  1234567890K  1234567890K 
   8  Down           1234567890K   1234567890K  1234567890K  1234567890K 
================================================================== 
ESC:exit     F:refresh 
U:page  up    D:page  down   L:page  left  R:page  right 

 

Port 

Same as the display explained for “current” option 

 

Link State/STP State 

Same as the display explained for “current” option   

 

Tx-Frame Counts 

Displays the number of cumulative transmission frames after system startup, using a 10-digit, right-justified value. 

 

Rx-Frame Counts 

Displays the number of cumulative receive frames after system startup, using a 10-digit, right-justified value. 

 

Rx-Bcast Counts 

Displays the number of cumulative receive broadcast frames after system startup, using a 10-digit, right-justified value. 

 

Rx-Mcast Counts 

Displays the number of cumulative receive multicast frames after system startup, using a 10-digit, right-justified value. 

 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands