manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 111

XG1200 User's Guide 

111/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

5.8.6 storm-control 

Function 

Enables broadcast storm control for the ports.

 

Use the no form to disable storm control.

 

Prompt 

xg(config-if)#, or xg(config-agg)# 

Command syntax 

storm-control 
no storm-control

 

 

Command type 

Configuration command 

Default 

None 

Note 

 

When storm state is detected, the port will be in violation state. After eliminating the cause of the storm state, clear the 
violation state with the "clear violation" command. 

Example 

Enable the storm control for Port 3 of the switch. 

xg(config)# interface port 3 
xg(config-if)# storm-control 

 

5.8.7 suppress-address-learning   

Function 

Disables the dynamic learning of the MAC address table for switch ports.

 

Use the no form to enable learning. 

Prompt 

xg(config-if)#, or xg(config-agg)# 

Command syntax 

suppress-address-learning 
no suppress-address-learning

 

Command type 

Configuration command 

Default 

None 

Example 

Disbale the dynamic learning of the MAC address table. 

xg(config-if)# suppress-address-learning 

 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands