manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 167

XG1200 User's Guide 

167/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

 

5.14.7 monitor vlan-traffic-counts 

Function 

Displays the received frame count of each VLAN. 

Prompt 

xg> or xg# 

Command syntax 

monitor vlan-traffic-counts { current | total } [interval <3-60>]

 

Parameter 

 

{ current | total } 

Specifies the statistics to be displayed. 

− 

current 

Displays the cumulative number of frames for each VLAN which have been received after startup of this 
command. 

− 

total 

Displays the cumulative number of frames for each VLAN which have been received after the system startup. 

 

interval <3-60> 

Specifies the statistics updating interval (in seconds). 

 

The default interval is 3 seconds. 

Command type 

Operation management command 

Output format (if "current" is specified) 

xg# monitor vlan-traffic-counts current 
VLAN Traffic Statistics(Current Frame Counts) 2005/08/22-12:12:15
=================================================================
VID   Rx-Frame     Rx-NonUcast 

   Counts       Counts 

---- ----------- ------------- 
   1  1234567890     1234567890 
  10             0              

 

0 

  20  1234567890K   1234567890K 
  30       25690M        

 

25690M 

  40       25690G        

 

25690G 

4094             0             

 

 

0 

=================================================================
ESC:exit     F:refresh 
U:page  up    D:page  down   L:page  left  R:page  right 

 

VID 

Displays the VID of the VLAN which has been set to collect its statistics. Statistics of each VLAN are displayed on a 
line. 

 

Specify the VLAN to collect its statistics using the "vlan-statistics collection" command. 

 

 

Rx-Frame Counts 

Displays the cumulative number of frames which have been received at the specified VLAN (after the startup of this 
command), using a 10-digit, right-justified value. 

 

Rx-NonUcast Counts 

Displays the cumulative number of multicast or broadcast frames which have been received at the specified VLAN 
(after the startup of this command), using a 10-digit, right-justified value. 

Output format (if "total" is specified) 

xg# monitor vlan-traffic-counts total 
VLAN Traffic Statistics(Total Frame Counts) 2005/08/22-12:12:15
===============================================================
VID   Rx-Frame     Rx-NonUcast 
       Counts       Counts      
---- ----------- ----------- 
   1   1234567890   1234567890  
  10             0              0  
  20  1234567890K  1234567890K 
  30       25690M        25690M 
  40       25690G        25690G 
4094             0              0  
===============================================================
ESC:exit     F:refresh 
U:page  up    D:page  down   L:page  left  R:page  right 

The values displayed in the “Counts” column are the ones cumulated after the system startup. Other values are the same 
as those displayed if the “current” option is specified. 

 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands