manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 224

XG1200 User's Guide 

224/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

A.2 

List of Event Logs 

This section provides message contents, explanation and actions to take that are associated with message ID and severity in 
ascending numerial order. The solution is not provided for messages for which you do not take action. 
 

A.2.1 env (Supervisory Control: 0

-

999) 

Message ID 

Severity 

Message/Explanation/Solution 

S0101 
ERROR 

%1$ Temperature is out of range. (%2$) 

 
Explanation 

A temperature error has been detected. 

 

[[Inserted string]]%1$: Location at which a temperature error was detected. 

Inlet: The temperature near the inlet 
Internal: The temperature inside the chassis 

 

[[Inserted string]]%2$: Temperature value 

 

Solution 

Perform the following concerning the set up of XG1200: 

 

Check that the air vent is not blocked. 

 

Check that the temperature of the set up location is within the limits set out by the operation guarantee.

   

If the message is displayed even though the XG1200 has been properly installed, note the message contents 
and contact your XG1200 sales representative.

 

S0102 
WARNING 

PWR-%1$ ALARM is detected.

 

 

Explanation

 

A power supply error has been detected.

 

 

[[Inserted string]]%1$: Power supply unit number

 

 

Solution

 

Replace the power supply unit.

 

S0103 
WARNING 

PWR-%1$ Hot Temperature. 

 

 
Explanation

 

A temperature error has been detected in the power supply unit.

 

 

[[Inserted string]]%1$: Power supply unit number 

 

Solution

 

Replace the power supply unit.

 

S0104 
WARNING 

PWR-%1$ is Off Line.

 

 

Explanation

 

It has been detected that no power is reaching the power supply unit.

 

 

[[Inserted string]]%1$: Power supply unit number 

 

Solution

 

Check for AC inputs.

 

P0105 
INFO 

PWR-%1$ is On Line. 

 

 

Explanation

 

Power has returned to power supply unit.

 

 

[[Inserted string]]%1$: Power supply unit number 

P0106 
INFO 

PWR-%1$ is Removed.

 

 

Explanation

 

It has been detected that power supply unit has been removed. 

 

[[Inserted string]]%1$: Power supply unit number 

 

Solution

 

If a message is received during times other than hot swapping, check the installation status.

 

P0107 
INFO 

PWR-%1$ is Inserted.

 

 

Explanation

 

It has been detected that power supply unit was installed.

 

 

[[Inserted string]]%1$: Power supply unit number 

 

Solution

 

If a message is received during times other than hot swapping, check the installation status.

 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands