manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 159

XG1200 User's Guide 

159/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

Output format (if "total" is specified) 

xg# monitor traffic-bytes total 
Traffic  Statistics(Total  Frame  Bytes)      2005/08/22-12:12:15 
============================================================== 
Port  Link  State/    Tx-Frame       Rx-Frame    
      STP  State     

 

Bytes           Bytes       

---- ------------- ------------  ------------ 
   1  Up/Discard     1234567890K   1234567890K 
   2  Down            1234567890G  

 

1234567890G 

   3  Up/Discard     1234567890M   1234567890M 
   4  Up/Learn      

 

1234567890T   1234567890T 

   5  Up/Forward      1234567890   

 

1234567890 

   6  Up/Forward      1234567890   

 

1234567890 

   7  Down            

 

1234567890   

 

1234567890 

   8  Down            

 

1234567890   

 

1234567890 

============================================================== 
ESC:exit     F:refresh 
U:page  up    D:page  down   L:page  left  R:page  right 

 

Port 

Same as the display explained for “current” option 

 

Link State/STP State 

Same as the display explained for “current” option 

 

Tx-Frame Bytes 

Displays the cumulative transmission byte count after system startup, using a 10-digit, right-justified value. 

 

Rx-Frame Bytes 

Displays the cumulative receive byte count after system startup, using a 10-digit, right-justified value. 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands