Home
/
Fujitsu
/
XG1200
/
User Manual

Fujitsu XG1200, User Manual

Share

Page: 202 / 258

Fujitsu XG1200 User Manual Download Page 202

XG1200 User's Guide

202/258

All Rights Reserved, Copyright (C) PFU LIMITED 2005

Example

Save the current system status data as the maintenance information in the non-volatile memory, and check the logging status
of the maintenance information using the “show maintenance” command.
Then, transfer the maintenance information to the “host1” TFTP server by naming it as the “mainte_collected date and time”
file.
Compare the file size of the maintenance information displayed on the screen and the size of the file stored at the destination.

xg# save maintenance
xg# show maintenance
Maintenance  Information        2005/08/22-20:58:17
==================================================
NO Type                           Occurred  Time
--- -------------------------- -------------------
1  system  dump                  2005/08/22-18:21:23
2  system  dump(dump  switch)   2005/08/22-20:57:58
3  system  dump(machine  check) 2005/08/22-20:58:14
==================================================
xg# tftp put-maintenance host1
Total file size: 480711 (bytes)

5.18.7 clear maintenance

Function

Clears the maintenance information from the non-volatile memory of the XG1200.

Prompt

xg#

Command syntax

clear maintenance

Command type

Operation management command

Notes

Issue the “clear maintenance” command only after you have checked the successful information transmission to the
TFTP server using the “tftp put-maintenance” command.

Example

Clear the maintenance information from the non-volatile memory of system hardware:

xg# clear maintenance

«
...
200
201
202
203
204
...
»

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands