manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 179

XG1200 User's Guide 

179/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

5.14.17 show statistics dataflow 

Function 

Displays statistics including the transmission and reception of flow control at each port and the data transmission type. 

Prompt 

xg> or xg# 

Command syntax 

show statistics dataflow

 

 

Command type 

Operation management command 

Output format 

xg# show statistics dataflow 
Dataflow Statistics(Total Counts)  2005/08/22-19:59:17 

[No.1] 
 Port                    :  1 
 Link State/ STP State: Up/Forward 
 Flow-Ctl  Mode         :  disabled 
 Forward  Counts        :  0 
 Flood  Counts          :  0 
 Rx-Pause  Counts       :  0 
 Tx-Pause  Counts       :  0 
 Full-Drop  Counts      :  0 
 VLAN-Drop  Counts      :  0 
[No.2] 
        
        

 

 

[No.]

 

Displays statistics of each port.

 

 

Port

 

Displays port numbers.   

 

Link State/STP State

 

Displays the port state in the Link State or STP State format.   
The Link State may indicate one of the following link states. 

− 

Down 

The port link is down.

 

− 

Up 

The port link is up.

 

The STP State displays the current port status based on the STP (Spanning Tree Protocol). Note that the STP State is 
not displayed if the Link State is Down. 

 

For port status details, see “Spanning Tree

 Protocol Port States

”

.

 

 

Flow-Ctl Mode

 

Displays the flow control setup of each port.

 

− 

Rx & Tx

 

Both transmission and reception of flow control are enabled.

 

− 

Rx

 

Only the reception of flow control is enabled.

 

 

Forward Counts

 

Displays the cumulative number of frames which have been forwarded normally (among the unicast frames received at 
each port after the system startup).

 

 

Flood Counts

 

Displays the cumulative number of flooded frames (among the unicast frames received at each port after the system 
startup).

 

 

Rx-Pause Counts

 

Displays the cumulative number of pause frames which have been received at each port after the system startup.

 

 

Tx-Pause Counts

 

Displays the cumulative number of pause frames which have been sent from each port after the system startup.

 

 

Full-Drop Counts

 

Displays the number of frames which have been discarded due to the saturated input buffer of the system among those 
received at each port after the system startup.

 

 

VLAN-Drop Counts

 

Displays the number of frames which have been discarded due to the reception of non-VLAN member frames that are 
not allowed to be forwarded among those received at each port after the system startup. 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands