Fujitsu XG1200 User Manual Download Page 128

Page: 128 / 258

XG1200 User's Guide

128/258

5.9.9 spanning-tree port-path-cost

Function

Sets a path cost of each port.
Use the no form to return to the default setup.

Prompt

xg(config-if)#, or xg(config-agg)#

Command syntax

spanning-tree port-path-cost <1-200000000>
no spanning-tree port-path-cost

Parameter

port-path-cost <1-200000000>

Sets a path cost of each port. It can be within the range of 1 to 200000000.

The following path cost values are recommended by IEEE802.1D.

IEEE802.1D (16bit)

IEEE802.1D (32bit)

Link speed

Recommended
range

Recommended
value

Recommended
range

Recommended
value

100M bps

10 - 60

20000 - 2000000

200000

1G bps

3 - 10

2000 - 200000

20000

10G bps

1 - 5

200 - 20000

2000

Command type

Configuration command

Configuration command Default

2 (16bit)
2000 (32bit)

Example

Set the path cost of switch port 2 to 3:

xg(config)# interface port 2
xg(config)# spanning-tree port-path-cost 3

Summary of Contents for XG1200































































































































































































































































Search results

Summary of Contents for XG1200

Reviews:

Brands by name

Popular brands

Fujitsu XG1200, User Manual

Search results

Summary of Contents for XG1200

Reviews:

Brands by name

Popular brands