Fujitsu XG1200 User Manual Download Page 198

Page: 198 / 258

XG1200 User's Guide

198/258

5.18.2 show log

Function

Displays system logs.

Prompt

xg#

Command syntax

show log { info | warning | error | critical } [ latest <1-10000> ]

Parameter

{ info | warning | error | critical }

Specifies a type of system log to be displayed.

−

info

Displays the INFO log.
The INFO log stores information (INFO) messages which report the system status of the XG1200.

−

warning

Displays the WARNING log.
The WARNING log stores the warning (WARNING) messages of the XG1200.

−

error

Displays the ERROR log.
The ERROR log stores the error (ERROR) messages of the XG1200.

−

critical

Displays the CRITICAL log.
The CRITICAL log stores the critical (CRITICAL) messages of the XG1200.

latest <1-10000>

Specifies the number of the latest log entries to be displayed within the range of 1 to 10000.
If omitted, all logs are displayed.

Command type

Operation management command

Output format

xg# show log info latest 1
May 25 22:08:33 xghost xgsh: XG INFO[P4001]: cmd-exec[3388]: show log info
| | | | | | | |

Month Day

Hours Min Sec

Function name

Severity

Message text

The XG1200's MessageID
Host name

Month

Displays the month when the event occurred.

Day

Displays the day when the event occurred.

Hours Min Sec

Displays the time (hours, minutes and seconds) when the event occurred.

Host name of the XG1200

Displays the time (hours, minutes and seconds) when the event occurred.

Function name

Displays the function name.

Severity

Indicates an importance level (or severity) of the message.

−

CRITICAL

Critical level.
The system has failed to continue its operation. Follow the instructions given by the message.

−

ERROR

Error level.
Part of system functions has failed although the system can continue its operations. Follow the instructions
given by the message.

−

WARNING

Warning level.
There is no problem in system operations although an error or a warning event has been detected. Check the
message information and determine the actions necessary to take.

−

INFO

Informational level.
This is an informational message showing the system status. No response is necessary.

MessageID

Displays the message ID in the “S message number” or “P message number” format.

−

Indicates that the message is notified with the SNMP trap.

−

Indicates that the message is not notified with the SNMP trap.

−

Message number

Displays a unique number for message identification. Read this message number to locate the message and
take the necessary actions.

Message text

Displays the message text.

Summary of Contents for XG1200































































































































































































































































Search results

Summary of Contents for XG1200

Reviews:

Brands by name

Popular brands

Fujitsu XG1200, User Manual

Search results

Summary of Contents for XG1200

Reviews:

Brands by name

Popular brands