manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 138

XG1200 User's Guide 

138/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

5.10.5 user-vlan-protocol-id 

Function 

The VLAN tag protocol ID (VPID or TPID) used for VLAN tag identification can be changed to the user-defined value of each 
port. 

 

The standard VLAN tag protocol ID has been defined to 0x8100 in IEEE 802.1Q. However, you can use the standard tag of 
IEEE 802.1Q as the multiple-tag VLAN which has been encapsulated with the user-defined VPID (or TPID) tag (*). 

 

*: Similar functions are called as Stacked VLAN, Nested VLAN, VLAN tunneling and 802.1Q in 802.1Q. 
 

 

 

For the frame format, see the TPID (Tag Protocol Identifier) in "

Tag VLAN Frame Format

". 

 

For the multiple-tag VLAN setup example and the frame flow, see "

Multiple VLAN

". 

 

Prompt 

xg(config-if)#, or xg(config-agg)# 

Command syntax 

user-vlan-protocol-id <0x05DD ~ 0xFFFF> 
no user-vlan-protocol-id

 

Parameter 

 

user-vlan-protocol-id <0x05DD ~ 0xFFFF> 

Specify the VPID (or TPID) using a hexadecimal integer beginning with 0x. It can be an integer of 0x05DD to 0xFFFF. 

Command type 

Configuration command 

Default 

0x8100 

Example 

Enter the interface edit mode for ports 1 to 3 and set the VPID (or TPID) to 0x2000. 

xg(config)# interface port range 1 3 
xg(config-if)# user-vlan-protocol-id 0x2000 

 
 

5.10.6 ingress-filter no-vlan-member-frame 

Function 

Enables VLAN ingress filtering. If the VLAN ingress filter is enabled, frames of the VLAN which the port is not registered as a 
member are discarded. 

 

Use the no form to disable the ingress filtering.

 

Prompt 

xg(config-if)#, or xg(config-agg)# 

Command syntax 

ingress-filter no-vlan-member-frame 
no ingress-filter no-vlan-member-frame

 

Parameter 

 

no-vlan-member-frame 

Discards the frames belonging to the VLAN which differs from the VLAN to which the port belongs. 

Command type 

Configuration command 

Default 

None 

Example 

Enter the Edit Interface mode for switch ports 1 to 3 and enable VLAN ingress filtering. 

xg(config)# interface port range 1 3 
xg(config-if)# ingress-filter no-vlan-member-frame 

 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands