manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 229

XG1200 User's Guide 

229/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

Message 

IDSeverity 

Message/Explanation/Solution 

S2109 
ERROR 

VLAN Table Operation error. %1$ 

 

Explanation

 

Failed to process the switch chip's VLAN management table.   

 

[[Inserted string]]%1$: Supplementary code for the error 

 

Solution

 

Note the message contents and contact your XG1200 sales representative. 

S2200 
WARNING 

MAC Table Error detected. %1$ 

 

Explanation

 

An uncorrectable error was detected in the MAC managment table. 

 

[[Inserted string]]%1$: Supplementary code for the error 

 

Solution

 

Note the message contents and contact your XG1200 sales representative. 

S2201 
WARNING 

Too Many MAC Table Error. Reset Switch LSI. 

 

Explanation

 

An uncorrectable error was detected repeatedly in the MAC management table and, therefore, switch chip was 
reset. 
 

Solution

 

Note the message contents and contact your XG1200 sales representative. 

S2202 
WARNING 

VLAN Table MBE detected. %1$ 

 

Explanation

 

An uncorrectable error was detected in the VLAN table. 

 

[[Inserted string]]%1$: Supplementary code for the error 

 

Solution

 

Note the message contents and contact your XG1200 sales representative. 

S2203 
WARNING 

VLAN Table SBE detected. %1$ 

 

Explanation

 

An uncorrectable error was detected in the VLAN table. It is automatically corrected by hardware. 

 

[[Inserted string]]%1$: Supplementary code for the error 

 

Solution

 

If the same message reappears after restarting, note the message contents and contact your XG1200 sales 
representative. 

S2204 
WARNING 

Too Many VLAN Table MBE Errors. Reset Switch LSI. 

 

Explanation

 

An uncorrectable error was detected repeatedly in the VLAN table and, therefore, switch chip was reset. 
 

Solution

 

If the same message reappears after restarting, note the message contents and contact your XG1200 sales 
representative. 

S2205 
WARNING 

Too Many VLAN Table SBE Error. Log Disabled. 

 

Explanation

 

A correctable error was detected repeatedly in the switch chip. Logging for this event is disabled. 
 

Solution

 

Note the message contents and contact your XG1200 sales representative. 

S2206 
WARNING 

Multicast State Table Error detected. %1$ 

 

Explanation

 

An uncorrectable error was detected in the switch chip. 

 

[[Inserted string]]%1$: Supplementary code for the error 

 

Solution

 

Note the message contents and contact your XG1200 sales representative. 

S2207 
WARNING 

Too Many MST Errors. Reset Switch LSI.

 

 

Explanation

 

An uncorrectable error was detected repeatedly in the switch chip and, therefore, switch chip was reset. 
 

Solution

 

Note the message contents and contact your XG1200 sales representative. 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands