manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 34

XG1200 User's Guide 

34/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

4.5 Spanning Tree Protocol (STP) 

The Spanning Tree Protocol (STP) is a function that prevents loops from occurring on a network. It is also possible to provide 
network redundancy by intentionally creating a loop. 

 

STP exclusively uses only one active path between network devices, and shuts out other paths, to avoid network loops. An 
active path is selected by comparing path costs defined on each path. After the comparison, the lowest cost path will be 
selected. If the selected path becomes disabled, STP will activate the lowest cost path among the paths remaining.

 

The XG1200 supports IEEE802.1w RSTP (Rapid Spanning Tree Protocol). The RSTP is upward compatible with IEEE9802.1D 
STP (Spanning Tree Protocol) and serves as an STP if the destination device supports the STP only. 

 

 

 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands