manualshive.com logo in svg

Fujitsu XG1200, User Manual

Share
Download
Fujitsu XG1200 User Manual Download Page 106

XG1200 User's Guide 

106/258

 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2005 

 

Link Status Detail 

Details of the port is displayed: 

Display 

Meaning 

PLUG-OUT 

XENPAK is taken off. 

LOW-PWR 

XENPAK is in LowPower state. 

LASI   

LASI Alarm is detected in XENPAK. 

PHY 

Access to XENPAK has failed. 

CLI 

The shutdown command has been executed. 

TMR 

Since the shutdown command and link-aggregation command have been executed, the 
port is down for a certain period of time. 

AGG-MIN 

The number of ports in link up state comprising an aggregation group has become less 
than the minimum number of ports. 

LF 

A local fault has been detected. 

RF 

A remote fault has been detected. 

LPT 

The link down state is notified through the link pass through function. 

SDL 

Frame discarding due to storm control has been detected. 

PSL 

Frame discarding due to port security violation has been detected. 

LAL 

Frame discarding due to loop back alert has been detected. 

SYS 

A system internal contradiction has been detected. 

 

STP State 

− 

Disabled 

The port is in a state to discard data traffic. 

− 

Learn 

The port is in the learning state. It prepares for forwarding data traffic. It discards data traffic. 

− 

Forward 

The port is ready to transmit data traffic. 

 

Flow Contorol 

− 

Rx Only 

A state in which only receiving process of PAUSE frame is enabled in flow control. 

− 

Rx and TX 

A state in which both sending and receiving process of PAUSE frame are enabled in flow control. 

 

Address Learning 

− 

Enabled 

Dynamic MAC address learning is enabled. 

− 

Disabled 

Dynamic MAC address learning is disabled. 

 

Multicast Forwarding 

− 

Forward-all 

All multicast frames will be forwarded (flooded). 

− 

Forward-unregistered-mac 

Multicast addresses yet to be registered in the static MAC address table, and multicast addresses registered as 
member ports will be forwarded (flooded). 

− 

Filter-unregistered-mac 

Only Multicast addresses registered as member ports in the static MAC address table will be forwarded. 

 

Port Security 

− 

Shutdown 

When a violation frame is detected, the port becomes in violation state, and in link down state. 

− 

Restrict 

When a violation frame is detected, the port becomes in violation state, and the violation frame will be 
discarded. 

− 

Disabled 

The port security is disabled. 

 

Storm Control 

− 

Enabled 

The storm control is enabled. 

− 

Disabled 

The storm control is disabled. 

 

Default Qos Priority 

Default priority <0-7> is displayed. 

 

Ingress Bandwidth 

The ingress rate limiting value of the port is displayed. The unit is Mbps.

 

For an aggregation group, the ingress rate limiting value, in which the ports comprising the aggregation group are 
totaled in "(total:<240-60000>)," is displayed. 

 

Vlan Information 

 

Port Default Vlan ID 

The default VLAN ID of the port is displayed. 

 

Vlan Member(tagged frame) 

VLAN, registered as a VLAN member (tagged), is displayed.

 

If it is not registered as a VLAN member (tagged), "None" is displayed. 

 

Vlan Member(untagged frame) 

VLAN, registered as a VLAN member (untagged), is displayed. 
If it is not registered as a VLAN member (untagged), "None" is displayed. 

Summary of Contents for XG1200



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands