Fujitsu XG1200 User Manual Download Page 244

Page: 244 / 258

XG1200 User's Guide

244/258

Appendix B

SNMP Traps

This appendix lists the SNMP traps supported by the XG1200.
Standard SNMP Traps

Trap name

RFC

Trap OID

coldStart 3418

1.3.6.1.6.3.1.1.5.1

linkDown 2863

1.3.6.1.6.3.1.1.5.3

linkUp 2863

1.3.6.1.6.3.1.1.5.4

authenticationFailure 3418

1.3.6.1.6.3.1.1.5.5

risingAlarm 2819

1.3.6.1.2.1.16.0.1

fallingAlarm 2819

1.3.6.1.2.1.16.0.2

newRoot 1493

1.3.6.1.2.1.17.0.1

topologyChange 1493

1.3.6.1.2.1.17.0.2

Enterprise-specific traps that are specific to the XG1200 report the following information.

Field

OID

Object name

Trap OID

1.3.6.1.4.1.211.1.127.61.101.2.0."message number"

xg1200***

1.3.6.1.4.1.211.1.127.61.101.2.10.1 xg1200TrapLevel

Variable list

1.3.6.1.4.1.211.1.127.61.101.2.10.2 xg1200TrapMessage

"xg1200***" differs from one event to another.

"xg1200TrapLevel" indicates the severity of an event. Their severities are defined as listed below.

Severity

Value

Critical 0
Error 1
Warning 2
Info 3

"xg1200TrapMessage" indicates a message that relates to an event.
The messages are the same as those for the event logs.

Summary of Contents for XG1200































































































































































































































































Search results

Summary of Contents for XG1200

Reviews:

Brands by name

Popular brands

Fujitsu XG1200, User Manual

Search results

Summary of Contents for XG1200

Reviews:

Brands by name

Popular brands