manualshive.com logo in svg

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Share
Download
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 99

PSU bays

PSU 1

PSU 2

Figure 64: PSU bays

6.3

Replacing the hot-plug PSU

Customer Replaceable
Unit (CRU)

Hardware: 5 minutes

Tools:

tool-less

CAUTION

▶

When replacing a PSU in a non-redundant PSU configuration, the
server must be switched off first.

▶

Replace the PSU after specifying the one that breaks down at work
by revitalization.

Preliminary steps

▶

"Locating the defective server" on page 39

.

▶

Check which PSU is defective.

A PSU is defective when the PSU status indicator lights orange. For more
information, see 

"Indicator on hot-plug PSU" on page 202

.

▶

Only when replacing a PSU in a non-redundant configuration: 

"Shutting 

down the server" on page 41

.

▶

Remove the power cord from the defective PSU, see 

"Disconnecting the 

power cord" on page 42

.

Power supply unit (PSU)

CX400 M6

Upgrade and Maintenance Manual

99

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands