Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 63

Page: 63 / 209

Figure 28: Attaching the left rack rail

▶

Move the left rack rail towards the rear side (2) while holding the positioning
clip (1). The mounting aid must lock in the corresponding hole.

▶

Release the positioning clip (1) after the designated position is reached.

▶

Move the left rail towards the front side (4) while holding the positioning clip
(3). The mounting aid must lock in the corresponding hole.

Figure 29: Adjusting the positioning clip

▶

Release the positioning clip (1) after the designated position is reached.

Basic hardware procedures

CX400 M6

Upgrade and Maintenance Manual

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Brands by name

Popular brands

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Brands by name

Popular brands