Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 86

Page: 86 / 209

4.12

Switching on the server nodes

CAUTION

▶

Follow the safety instructions in

"Important information" on page 25

Controls and indicators are the same for the CX2550 M6 and the
CX2560 M6.

▶

If applicable, connect all external cables to the server node.

Figure 61: Controls and indicators of the server node

ID indicator

On/Off button / Power-on indicator

▶

Press the On/Off button either on the rear or on the corresponding front
panel to start up the server node. The power-on indicator does lit green.

For more information, see

"Node-related indicators" on page 199

Basic hardware procedures

Upgrade and Maintenance Manual

CX400 M6

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Brands by name

Popular brands

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Brands by name

Popular brands