manualshive.com logo in svg

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Share
Download
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 131

CAUTION

Installing procedures involving Upgrade and Repair Units must be
performed exclusively by Fujitsu service personnel or technicians
trained by Fujitsu. Please note that unauthorized interference with the
system will void the warranty and exempt the manufacturer from all
liability.

Preliminary steps

▶

Shut down the server nodes, see 

"Shutting down the server" on page 41

.

▶

"Disconnecting the power cord" on page 42

.

▶

If applicable, remove the front bezel, see 

"Removing the front bezel" on 

page 48

.

▶

Remove all HDD/SSD modules from the relevant HDD/SSD cage, see

"Removing a 2.5-inch HDD/SSD module" on page 116

.

▶

If applicable, remove all 2.5-inch HDD/SSD dummy module, see 

"Removing 

a 2.5-inch HDD/SSD dummy module" on page 113

.

▶

"Removing server nodes from the server enclosure" on page 43

.

▶

"Removing the defective hot-plug PSU" on page 100

.

▶

"Extending the server enclosure out of the rack" on page 49

.

▶

"Removing the top covers" on page 54

.

▶

"Removing the defective high speed riser module" on page 151

.

▶

Remove all fan modules, see 

"Removing the fan module" on page 147

.

▶

"Removing the fan cage" on page 120

.

▶

"Removing the power distribution board kit" on page 157

.

▶

"Removing the 2.5-inch HDD backplane" on page 122

.

Hard disk drive (HDD) / solid state disk (SSD)

CX400 M6

Upgrade and Maintenance Manual

131

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands